FR98 Kominoshe Zjarrfikësi Pyjesh Wildland
Kjo kominoshe është perfekte për kërkesat e motit të ngrohtë të terreneve të ashpra në zjarr. E ndërtuar me peshë të lehtë me një pëlhurë inovative flakë-duruese me veçori speciale për të mbrojtur përdoruesin nga rreziqet që kanë lidhje me flakët jasht shtëpise.
Veçoritë
Mbrojtje kundër nxehtesise rezatuese dhe konvektive
Reflektim i Verdhe/Argjende
Xhep për radio i dizenjuar për tu perputhur me të gjitha madhesite
Xhepa të medhenj të kembet
Mbrojtje me Shtresë të dyfishte për gjunjte
Mbrojtese fyti ne pjesen para të qafes
Menge të trikotuara për ngrojtesi dhe rehati
Qepje të dyfishte për me Shume Rezistence
Ambalazhimi i produktit është i pershatshem për tu reklamuar ne dyqan
pëlhurë e klasifikuar me UPF 40+ për të bllokuar 98% rrezeve UV
3 xhepa për vendosje të sigurte
Ka Shirit reflektues flake durues cilesia e larte
Zinxhir i Dyanshem për Hapje të Shpejte
Lak për radio
Certifikim CE
CE-CAT III
Materialet:
Pëlhura Jashtme/Kryesore: Bizflame Plus: 99% Pambuk, 1% Fibra Karboni 280g
STANDARTET
EN ISO 11612 (A1+A2, B1, C1)
EN 15614
EN 1149-5
PORTWEST
For over 117 years we’ve possessed an unrelenting ambition to produce the world’s most trusted and requested protective wear. Through the decades, we have continuously proven our dedication to quality, producing world beating safety garments, foot protection, hand protection and PPE, while pushing the boundaries in protection technologies. Technologies that make the workplace a safer place.
EN ISO 11612 Heat & Flame
Letter A (EN 15025) This test consists of applying a flame to a fabric sample for 10 seconds. To pass the test, the after flame & smoulder times and formation of holes must be within the tolerances within the standard. The application of a flame can take place in two ways: Code Letter A1 Surface Ignition, ISO15025 A Procedure A (leads to Class A1), the flame is applied horizontally to the face of the fabric No specimen shall permit any part of the lowest boundary of any flame to reach the upper or either vertical edges No specimen shall give hole formation of 5mm or greater in any direction, except for an inter-lining that is used for specific protection other than heat and flame protection. No specimen shall give flaming or molten debris The mean value of after flame time shall be ≤ 2s The mean value of afterglow time shall be ≤ 2s Code Letter A1 Edge Ignition, ISO15025 B Procedure B (leads to Class A2), the flame is applied to the bottom edge of the fabric sample. No specimen shall permit any part of the lowest boundary of any flame to reach the upper or either vertical edges No specimen shall give flaming or molten debris The mean value of after flame time shall be ≤ 2s The mean value of afterglow time shall be ≤ 2s Letter B (ISO 9151) Convective Heat: determination of the heat transmission when exposed to flames. The sample is held above the flame and the rise in temperature on the topside of the sample is measured with a calorimeter. The length of time the sample can remain exposed before its temperature rises by 24 °C is determined. B1: 4 < 10 seconds, B2: 10 < 20 seconds, B3: 21 seconds and longer Letter C (ISO 6942) Exposure to Radiant Heat. In this test, a fabric sample is exposed to radiant heat (infrared rays). The temperature on the reverse (unexposed) side of the sample is registered using a calorimeter. Subsequently, the length of time the sample the sample can remain exposed before its temperature rises by 24°C is measured. The test procedure is the same as ISO 11611, but the classification is different: C1: 7 < 20 seconds, C2: 20 < 50 seconds, C3: 50 < 95 seconds, C4: 95 seconds and longer Letter D and E (ISO 9185) D = Aluminium E = Molten Iron Determining the level of protection against spatters of molten metal. A membrane (with similar properties to human skin) is attached to the reverse of the fabric sample sequentially rising quantities of molten metal (Aluminium or Iron as applicable) are splashed on the sample. The quantity of molten metal which deforms the membrane is determined. The classification for molten aluminium is: D1: 100 < 200 grams, D2: 200 <350 grams, D3: 350 grams and more The classification for molten iron is: E1: 60 < 120 grams, E2: 120 < 200 grams, E3: 200 grams and more Letter F (ISO 12127) This is a new test to establish a value for contact heat. The classification in this respect: F1: 5 < 10 seconds, F2: 10 < 15 seconds, F3: 15 seconds and longerDetails
EN 1149 Anti-Static (ATEX)
This standard specifies PPE Clothing used in explosive environments (i.e. ATEX) where there is a risk that the garments could create sparks (source of ignition), which in turn could ignite explosive materials. Anti-Static garments marked EN 1149-5 are intended to be worn in Atex zones 1, 2, 20, 21 and 22. In oxygen enriched atmospheres or in zone 0, the Anti-Static garments should not be used without first being approved by a qualified Safety Engineer, as wear and tear can affect the protection of the garment and it is crucial that they are worn the correct way in these environments.Details
EN 15614 Wildland Firefighting Clothing
The EN 15614:2007 standard states the different performance requirements wildland firefighter clothing has to comply with. As forest fires primarily occur in the summer, the radiant heat can be very high for a very long time. Clothing that meets that standard, helps prevent the metabolic heat from becoming too high. The right garments for these conditions have to be light without causing heat stress.Details
Share this product:
| Garment Size | S - Small or M - Medium or L - Large or XL - XLarge or XXL - XXLarge |
| Color | NAR Navy |
Once the user has seen at least one product this snippet will be visible.