FR706 Bizflame 88/12 FR Ανακλαστική Βραδυφλεγής Πουκάμισο
Αυτό το κομψό πουκάμισο είναι ελαφρύ και άνετο. Η μέγιστη προστασία είναι εγγυημένη με μόνιμη αντίσταση στη φλόγα και προστασία ARC2 από ηλεκτρικό τόξο. Η ουρά του πουκαμίσου θα παραμείνει κουμπωμένη κατά τη διάρκεια της κίνησης και όλη την ημέρα. Τα εύχρηστα χαρακτηριστικά περιλαμβάνουν ρυθμιζόμενες μανσέτες με κουμπιά και τσέπες στο στήθος.
Χαρακτηριστικά:
- Ελαφρύ και άνετο
- Διπλή προστασία από κινδύνους
- Δύο τσέπες στο στήθος με κλείσιμο με κουμπί και πτερύγιο
- Διαίρεση στυλό στην αριστερή τσέπη
- Το στρίφωμα της ουράς του πουκαμίσου παραμένει κουμπωμένο
- Μανσέτες με κουμπιά για ασφαλή και άνετη εφαρμογή
- Διατίθεται σε μεγέθη έως 6XL
- 2 τσέπες για ασφαλή αποθήκευση
- Ύφασμα 40+ UPF για να μπλοκάρει το 98% των ακτίνων UV
- Πιστοποιημένο CE
- CE-CAT III
Πληροφορίες για το ύφασμα:
Bizflame 88/12: 88% βαμβάκι, 12% νάιλον 237 γρ.
Πρότυπα:
ASTM F1959/F1959M-12 ATPV 8.2 CAL/CM2 (HAF 69.1%)
ASTM F1506
NFPA® 2112
NFPA® 70E
EN ISO 11612 A1+A2, B1, C1
PORTWEST
For over 117 years we’ve possessed an unrelenting ambition to produce the world’s most trusted and requested protective wear. Through the decades, we have continuously proven our dedication to quality, producing world beating safety garments, foot protection, hand protection and PPE, while pushing the boundaries in protection technologies. Technologies that make the workplace a safer place.
EN ISO 11612 Heat & Flame
Letter A (EN 15025) This test consists of applying a flame to a fabric sample for 10 seconds. To pass the test, the after flame & smoulder times and formation of holes must be within the tolerances within the standard. The application of a flame can take place in two ways: Code Letter A1 Surface Ignition, ISO15025 A Procedure A (leads to Class A1), the flame is applied horizontally to the face of the fabric No specimen shall permit any part of the lowest boundary of any flame to reach the upper or either vertical edges No specimen shall give hole formation of 5mm or greater in any direction, except for an inter-lining that is used for specific protection other than heat and flame protection. No specimen shall give flaming or molten debris The mean value of after flame time shall be ≤ 2s The mean value of afterglow time shall be ≤ 2s Code Letter A1 Edge Ignition, ISO15025 B Procedure B (leads to Class A2), the flame is applied to the bottom edge of the fabric sample. No specimen shall permit any part of the lowest boundary of any flame to reach the upper or either vertical edges No specimen shall give flaming or molten debris The mean value of after flame time shall be ≤ 2s The mean value of afterglow time shall be ≤ 2s Letter B (ISO 9151) Convective Heat: determination of the heat transmission when exposed to flames. The sample is held above the flame and the rise in temperature on the topside of the sample is measured with a calorimeter. The length of time the sample can remain exposed before its temperature rises by 24 °C is determined. B1: 4 < 10 seconds, B2: 10 < 20 seconds, B3: 21 seconds and longer Letter C (ISO 6942) Exposure to Radiant Heat. In this test, a fabric sample is exposed to radiant heat (infrared rays). The temperature on the reverse (unexposed) side of the sample is registered using a calorimeter. Subsequently, the length of time the sample the sample can remain exposed before its temperature rises by 24°C is measured. The test procedure is the same as ISO 11611, but the classification is different: C1: 7 < 20 seconds, C2: 20 < 50 seconds, C3: 50 < 95 seconds, C4: 95 seconds and longer Letter D and E (ISO 9185) D = Aluminium E = Molten Iron Determining the level of protection against spatters of molten metal. A membrane (with similar properties to human skin) is attached to the reverse of the fabric sample sequentially rising quantities of molten metal (Aluminium or Iron as applicable) are splashed on the sample. The quantity of molten metal which deforms the membrane is determined. The classification for molten aluminium is: D1: 100 < 200 grams, D2: 200 <350 grams, D3: 350 grams and more The classification for molten iron is: E1: 60 < 120 grams, E2: 120 < 200 grams, E3: 200 grams and more Letter F (ISO 12127) This is a new test to establish a value for contact heat. The classification in this respect: F1: 5 < 10 seconds, F2: 10 < 15 seconds, F3: 15 seconds and longerDetails
Share this product:
| Μέγεθος ρούχων | S - Small or M - Medium or L - Large or XL - XLarge or XXL - XXLarge or XXXL - 3XLARGE or 4XL - 4XLarge or 5XL - 5XLarge or 6XL - 6XLarge |
| Χρώμα | NAR Ναυτικό μπλέ |
Once the user has seen at least one product this snippet will be visible.